CE certification

CE Introduction:

In the EU market, the "CE" mark is a mandatory certification mark. Whether products produced by enterprises within the EU or products produced in other countries, if they want to circulate freely in the EU market, they must be affixed with the "CE" mark to indicate that the products meet the basic requirements of the EU New Method for Technical Coordination and Standardization. This is a mandatory requirement of EU laws on products.

CE mark:

1. The "CE" mark is a safety certification mark, which is regarded as a passport for manufacturers to open and enter the European market. All products with the "CE" mark can be sold in the EU member states without meeting the requirements of each member state, thus realizing the free circulation of goods within the EU member states.

2. The "CE" mark must be affixed in a prominent position. The "CE" mark must be affixed by the manufacturer or the designated representative located in the European Union. The manufacturer (within the EU or from outside the EU) is the ultimate responsible person for making the products meet the basic requirements of the Directive. The manufacturer can also designate a plenipotentiary representative within the EU, and the person responsible for putting the products on the market will assume the responsibility of the manufacturer.

In principle, in order to ensure that the products meet all the requirements of the relevant directives, the "CE" mark can be affixed on the products only after all the conformity assessment procedures have been completed. The work of affixing the "CE" mark is often completed after the production stage. For example, first stick the "CE" sign on the parameter label, and then stick the "CE" sign on the product after the inspection. However, if the "CE" mark is affixed by die stamping or casting, forming an integral part of the product or parts, the mark can be affixed at the production stage, as long as the product is verified to be qualified in the conformity assessment procedure of the entire production process.

The "CE" mark indicates that the product complies with the most basic public interest involved in the Directive, so it can be regarded as the basic information transmitted to the authorities of Member States and relevant solids. Therefore, the "CE" mark affixed to the product must be in a prominent position, clear and not easy to smear. In general, the "CE" mark is affixed to the product or its parameter label. If the "CE" mark cannot be directly affixed to the product, it can also be affixed to the product packaging or product attached documents. However, it is necessary to prove the reason why the "CE" mark cannot be affixed to the product, such as some explosive articles, or due to certain technical and economic conditions, Or because the size requirements of the "CE" mark can not be guaranteed to be met, or the requirements of clear and hard to apply the mark can not be met, in these cases, the "CE" mark can be pasted on the package or attached documents.

3. The minimum height of the "CE" mark shall not be less than 5MM, and the reduction or expansion shall be carried out in proportion.

4. Which products are applicable to the "CE" mark:

CE certification directives and applicable products:

name

Major Directive Number

Applicable products

Low voltage command

（LVD）

2014/35/EU

It is designed to use electrical equipment with rated voltage of AC 50V-1000V and DC 75V-1500V, including household and similar equipment, lighting fixtures, low-voltage appliances, wires and cables, electric tools, small power motors, safety transformers and similar equipment

EMC Directive

（EMC）

2014/30/EU

EMC (electromagnetic interference EMI and electromagnetic immunity EMS) may cause electromagnetic interference and its performance may be affected by such interference, such as audio and video equipment, information technology equipment, computers and peripheral equipment

Radio and Telecommunications Terminal Equipment Directive

(RED)

2014/53/EU

It refers to a kind of communication products or related components that use the ground/air wireless communication spectrum to transmit and/or receive radio waves. Such as: telephone, mobile phone, remote controller, data terminal, multimedia terminal, telecommunication terminal, etc

Toy Directive

（EN71）

2009/48/EC

Plush toys, plastic toys, electric toys, remote control toys, etc

Personal Protective Equipment Directive

（PPE）

89/686/EEC

It refers to devices or appliances worn on or carried by people to prevent health and safety hazards; Including helmets, protective eyes (including solar eyes), protective clothing, protective shoes, knee pads, gas masks and other equipment

Machinery Directive

（MD）

2006/42/EC

A machine consisting of several parts or accessories connected together, of which at least one component can operate. Such as machine tools, sewing machines, weeding machines and other industrial machinery; Hand tools such as knife shears and pincers

General Medical Devices Directive

（MDD）

93/42/EEC

Nuclear magnetic resonance instrument, ultrasonic diagnosis and treatment instrument, infusion pump, dressing, disposable product, contact lens, blood bag, catheter, etc

General Product Safety Directive

（GPSD）

2001/95/EC

Outdoor furniture, fitness equipment, child care products, fixed training equipment, bicycles, etc

General Building Directive

（CPD）

89/106/EEC

Stone, ceramic tile, glass, concrete admixture, aluminum plastic composite board, fire hose, wood, etc

Pressure equipment

（PED）

97/23/EC

Valves, fire extinguishers, pressure gauges, air cabinets, tower troughs, pipelines, pipe fittings, steam equipment, etc

CE certification process

Step 1: Apply for Application

1. Fill in the application form

2. Application company information form

3. Provide product data

Step 2: Quotation

Determine the test standard, test time and corresponding costs according to the data provided

Step 3: Pay

After confirming the quotation, the applicant shall sign the application form and service agreement and pay the full project fee or at least 50%.

Step 4: Testing

The laboratory shall carry out a full set of tests on the applied products and the difference test of relevant models according to the relevant EU test standards

Step 5: Pass the test and complete the report

Step 6: Complete the project and issue the CE certificate

If you are not clear, please feel free to contact me.

Contact information of the recognition center:

Tel.: 0592-2650351 Email: shunjia.xmn@qq.com